[Code of Federal Regulations]
[Title 29, Volume 5]
[Revised as of January 1, 2007]
From the U.S. Government Printing Office via GPO Access
[CITE: 29CFR1910.6]
[Page 92-100]
TITLE 29--LABOR
CHAPTER XVII--OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT
OF LABOR
PART 1910_OCCUPATIONAL SAFETY AND HEALTH STANDARDS--Table of Contents
Subpart A_General
Sec. 1910.6 Incorporation by reference.
(a)(1) The standards of agencies of the U.S. Government, and
organizations which are not agencies of the U.S. Government which are
incorporated by reference in this part, have the same force and effect
as other standards in this part. Only the mandatory provisions (i.e.,
provisions containing the word ``shall'' or other mandatory language) of
standards incorporated by reference are adopted as standards under the
Occupational Safety and Health Act.
(2) Any changes in the standards incorporated by reference in this
part and an official historic file of such changes are available for
inspection at the national office of the Occupational Safety and Health
Administration, U.S. Department of Labor, Washington, DC 20210.
(3) The materials listed in paragraphs (b) through (w) of this
section are incorporated by reference in the corresponding sections
noted as they exist on the date of the approval, and a notice of any
change in these materials will be published in the Federal Register.
These incorporations by reference were approved by the Director of the
Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR part 51.
(4) Copies of the following standards that are issued by the
respective private standards organizations may be obtained from the
issuing organizations. The materials are available for purchase at the
corresponding addresses of the private standards organizations noted
below. In addition, all are available for inspection through the OSHA
Docket Office, room N2625, U.S. Department of Labor, 200 Constitution
Ave., Washington, DC 20210, or any of its regional offices or at the
National Archives and Records Administration (NARA). For information on
the availability of this material at NARA, call 202-741-6030, or go to:
http://www.archives.gov/federal--register/code--of--federal--
regulations/ibr--locations.html.
(b) The following material is available for purchase from the
American Conference of Governmental Industrial Hygienists (ACGIH), 1014
Broadway, Cincinnati OH 45202:
(1) ``Industrial Ventilation: A Manual of Recommended Practice''
(22nd ed., 1995), incorporation by reference (IBR) approved for Sec.
1910.124(b)(4)(iii).
(2) Threshold Limit Values and Biological Exposure Indices for 1986-
87 (1986), IBR approved for Sec. 1910.120, PEL definition.
(c) The following material is available for purchase from the
American Society of Agricultural Engineers (ASAE), 2950 Niles Road, Post
Office Box 229, St. Joseph, MI 49085:
(1) ASAE Emblem for Identifying Slow Moving Vehicles, ASAE S276.2
(1968), IBR approved for Sec. 1910.145(d)(10).
(2) [Reserved]
(d) The following material is available for purchase from the
Agriculture
[[Page 93]]
Ammonia Institute-Rubber Manufacturers (AAI-RMA) Association, 1400 K St.
NW, Washington DC 20005:
(1) AAI-RMA Specifications for Anhydrous Ammonia Hose, IBR approved
for Sec. 1910.111(b)(8)(i).
(2) [Reserved]
(e) The following material is available for purchase from the
American National Standards Institute (ANSI), 11 West 42nd St., New
York, NY 10036:
(1) ANSI A10.2-44 Safety Code for Building Construction, IBR
approved for Sec. 1910.144(a)(1)(ii).
(2) ANSI A10.3-70 Safety Requirements for Explosive-Actuated
Fastening Tools, IBR approved for Sec. 1910.243(d)(1)(i).
(3) ANSI A11.1-65 (R 70) Practice for Industrial Lighting, IBR
approved for Sec. Sec. 1910.219(c)(5)(iii); 1910.261 (a)(3)(i),
(c)(10), and (k)(21); and 1910.265(c)(2).
(4) ANSI A11.1-65 Practice for Industrial Lighting, IBR approved for
Sec. Sec. 1910.262(c)(6) and 1910.265(d)(2)(i)(a).
(5) ANSI A12.1-67 Safety Requirements for Floor and Wall Openings,
Railings, and Toe Boards, IBR approved for Sec. Sec. 1910.66 appendix
D, (c)(4); 1910.68 (b)(4) and (b)(8)(ii); 1910.261 (a)(3)(ii), (b)(3),
(c)(3)(i), (c)(15)(ii), (e)(4), (g)(13), (h)(1), (h)(3)(vi), (j)(4) (ii)
and (iv), (j)(5)(i), (k)(6), (k)(13)(i), and (k)(15).
(6) ANSI A13.1-56 Scheme for the Identification of Piping Systems,
IBR approved for Sec. Sec. 1910.253(d)(4)(ii); 1910.261(a)(3)(iii);
1910.262(c)(7).
(7) ANSI A14.1-68 Safety Code for Portable Wood Ladders,
Supplemented by ANSI A14.1a-77, IBR approved for Sec. 1910.261
(a)(3)(iv) and (c)(3)(i).
(8) ANSI A14.2-56 Safety Code for Portable Metal Ladders,
Supplemented by ANSI A14.2a-77, IBR approved for Sec. 1910.261
(a)(3)(v) and (c)(3)(i).
(9) ANSI A14.3-56 Safety Code for Fixed Ladders, IBR approved for
Sec. Sec. 1910.68(b) (4) and (12); 1910.179(c)(2); and 1910.261
(a)(3)(vi) and (c)(3)(i).
(10) ANSI A17.1-65 Safety Code for Elevators, Dumbwaiters and Moving
Walks, Including Supplements, A17.1a (1967); A17.1b (1968); A17.1c
(1969); A17.1d (1970), IBR approved for Sec. 1910.261 (a)(3)(vii),
(g)(11)(i), and (l)(4).
(11) ANSI A17.2-60 Practice for the Inspection of Elevators,
Including Supplements, A17.2a (1965), A17.2b (1967), IBR approved for
Sec. 1910.261(a)(3)(viii).
(12) ANSI A90.1-69 Safety Standard for Manlifts, IBR approved for
Sec. 1910.68(b)(3).
(13) ANSI A92.2-69 Standard for Vehicle Mounted Elevating and
Rotating Work Platforms, IBR approved for Sec. 1910.67 (b)(1), (2),
(c)(3), and (4) and 1910.268(s)(1)(v).
(14) ANSI A120.1-70 Safety Code for Powered Platforms for Exterior
Building Maintenance, IBR approved for Sec. 1910.66 app. D (b) through
(d).
(15) ANSI B7.1-70 Safety Code for the Use, Care and Protection of
Abrasive Wheels, IBR approved for Sec. Sec. 1910.94(b)(5)(i)(a);
1910.215(b)(12); and 1910.218(j)(5).
(16) ANSI B15.1-53 (R 58) Safety Code for Mechanical Power
Transmission Apparatus, IBR approved for Sec. Sec. 1910.68(b)(4) and
1910.261 (a)(3)(ix), (b)(1), (e)(3), (e)(9), (f)(4), (j)(5)(iv),
(k)(12), and (l)(3).
(17) ANSI B20.1-57 Safety Code for Conveyors, Cableways, and Related
Equipment, IBR approved for Sec. Sec. 1910.218(j)(3); 1910.261
(a)(3)(x), (b)(1), (c)(15)(iv), (f)(4), and (j)(2); 1910.265(c)(18)(i).
(18) ANSI B30.2-43 (R 52) Safety Code for Cranes, Derricks, and
Hoists, IBR approved for Sec. 1910.261 (a)(3)(xi), (c)(2)(vi), and
(c)(8) (i) and (iv).
(19) ANSI B30.2.0-67 Safety Code for Overhead and Gantry Cranes, IBR
approved for Sec. Sec. 1910.179(b)(2); 1910.261 (a)(3)(xii), (c)(2)(v),
and (c)(8) (i) and (iv).
(20) ANSI B30.5-68 Safety Code for Crawler, Locomotive, and Truck
Cranes, IBR approved for Sec. Sec. 1910.180(b)(2) and
1910.261(a)(3)(xiii).
(21) ANSI B30.6-69 Safety Code for Derricks, IBR approved for
Sec. Sec. 1910.181(b)(2) and 1910.268(j)(4)(iv) (E) and (H).
(22) ANSI B31.1-55 Code for Pressure Piping, IBR approved for Sec.
1910.261(g)(18)(iii).
(23) ANSI B31.1-67, IBR approved for Sec. 1910.253(d)(1)(i)(A)
(24) ANSI B31.1a-63 Addenda to ANSI B31.1 (1955), IBR approved for
Sec. 1910.261(g)(18)(iii).
(25) ANSI B31.1-67 and Addenda B31.1 (1969) Code for Pressure
Piping, IBR approved for Sec. Sec. 1910.103(b)(1)(iii)(b);
[[Page 94]]
1910.104(b)(5)(ii); 1910.218 (d)(4) and (e)(1)(iv); and 1910.261
(a)(3)(xiv) and (g)(18)(iii).
(26) ANSI B31.2-68 Fuel Gas Piping, IBR approved for Sec.
1910.261(g)(18)(iii).
(27) ANSI B31.3-66 Petroleum Refinery Piping, IBR approved for Sec.
1910.103(b)(3)(v)(b).
(28) ANSI B31.5-66 Addenda B31.5a (1968) Refrigeration Piping, IB
approved for Sec. Sec. 1910.103(b)(3)(v)(b) and 1910.111(b)(7)(iii).
(29) ANSI B56.1-69 Safety Standard for Powered Industrial Trucks,
IBR approved for Sec. Sec. 1910.178(a) (2) and (3) and 1910.261
(a)(3)(xv), (b)(6), (m)(2), and (m)(5)(iii).
(30) ANSI B57.1-65 Compressed Gas Cylinder Valve Outlet and Inlet
Connections, IBR approved for Sec. 1910.253(b)(1)(iii).
(31) [Reserved]
(32) ANSI B175.1-1991, Safety Requirements for Gasoline-Powered
Chain Saws 1910.266(e)(2)(i).
(33) ANSI C1-71 National Electrical Code, IBR approved for Sec.
1910.66 appendix D (c)(22) (i) and (vii).
(34) ANSI C33.2-56 Safety Standard for Transformer-Type Arc Welding
Machines, IBR approved for Sec. 1910.254(b)(1).
(35) [Reserved]
(36) ANSI H23.1-70 Seamless Copper Water Tube Specification, IBR
approved for Sec. 1910.110(b) (8)(ii) and (13)(ii)(b)(1).
(37) ANSI H38.7-69 Specification for Aluminum Alloy Seamless Pipe
and Seamless Extruded Tube, IBR approved for Sec. 1910.110(b)(8)(i).
(38) ANSI J6.4-71 Standard Specification for Rubber Insulating
Blankets, IBR approved for Sec. 1910.268 (f)(1) and (n)(11)(v).
(39) ANSI J6.6-71 Standard Specification for Rubber Insulating
Gloves, IBR approved for Sec. 1910.268 (f)(1) and (n)(11)(iv).
(40) ANSI K13.1-67 Identification of Gas Mask Canisters, IBR
approved for Sec. 1910.261 (a)(3)(xvi) and (h)(2)(iii).
(41) ANSI K61.1-60 Safety Requirements for the Storage and Handling
of Anhydrous Ammonia, IBR approved for Sec. 1910.111(b)(11)(i).
(42) ANSI K61.1-66 Safety Requirements for the Storage and Handling
of Anhydrous Ammonia, IBR approved for Sec. 1910.111(b)(11)(i).
(43) ANSI O1.1-54 (R 61) Safety Code for Woodworking Machinery, IBR
approved for Sec. 1910.261 (a)(3)(xvii), (e)(7), and (i)(2).
(44) ANSI S1.4-71 (R 76) Specification for Sound Level Meters, IBR
approved for Sec. 1910.95 appendixes D and I.
(45) ANSI S1.11-71 (R 76) Specification for Octave, Half-Octave and
Third-Octave Band Filter Sets, IBR approved for Sec. 1910.95 appendix
D.
(46) ANSI S3.6-69 Specifications for Audiometers, IBR approved for
Sec. 1910.95(h)(2) and (5)(ii) and appendix D.
(47) ANSI Z4.1-68 Requirements for Sanitation in Places of
Employment, IBR approved for Sec. 1910.261 (a)(3)(xviii) and
(g)(15)(vi).
(48) [Reserved]
(49) ANSI Z9.1-51 Safety Code for Ventilation and Operation of Open
Surface Tanks, IBR approved for Sec. Sec. 1910.94(c)(5)(iii)(e) and
1910.261 (a)(3)(xix), (g)(18)(v), and (h)(2)(i).
(50) ANSI Z9.1-71 Practices for Ventilation and Operation of Open-
Surface Tanks, IBR approved for Sec. 1910.124(b)(4)(iv).
(51) ANSI Z9.2-60 Fundamentals Governing the Design and Operation of
Local Exhaust Systems, IBR approved for Sec. Sec. 1910.94(a)(4)(i)
introductory text, (a)(6) introductory text, (b)(3)(ix), (b)(4)(i) and
(ii), (c)(3)(i) introductory text, (c)(5)(iii)(b), and (c)(7)(iv)(a);
1910.261(a)(3)(xx), (g)(1)(i) and (iii), and (h)(2)(ii).
(52) ANSI Z9.2-79 Fundamentals Governing the Design and Operation of
Local Exhaust Systems, IBR approved for Sec. 1910.124(b)(4)(i).
(53) ANSI Z12.12-68 Standard for the Prevention of Sulfur Fires and
Explosions, IBR approved for Sec. 1910.261 (a)(3)(xxi), (d)(1)(i),
(f)(2)(iv), and (g)(1)(i).
(54) ANSI Z12.20-62 (R 69) Code for the Prevention of Dust
Explosions in Woodworking and Wood Flour Manufacturing Plants, IBR
approved for Sec. 1910.265(c)(20)(i).
(55) ANSI Z21.30-64 Requirements for Gas Appliances and Gas Piping
Installations, IBR approved for Sec. 1910.265(c)(15).
(56) ANSI Z24.22-57 Method of Measurement of Real-Ear Attenuation of
Ear Protectors at Threshold, IBR approved for Sec.
1910.261(a)(3)(xxii).
[[Page 95]]
(57) ANSI Z33.1-61 Installation of Blower and Exhaust Systems for
Dust, Stock, and Vapor Removal or Conveying, IBR approved for Sec. Sec.
1910.94(a)(4)(i); 1910.261 (a)(3)(xxiii) and (f)(5); and
1910.265(c)(20)(i).
(58) ANSI Z33.1-66 Installation of Blower and Exhaust Systems for
Dust, Stock, and Vapor Removal or Conveying, IBR approved for Sec.
1910.94(a)(2)(ii).
(59) ANSI Z35.1-68 Specifications for Accident Prevention Signs, IBR
approved for Sec. 1910.261 (a)(3)(xxiv) and (c)(16).
(60) ANSI Z41.1-67 Men's Safety Toe Footwear, IBR approved for
Sec. Sec. 1910.94(a)(5)(v); 1910.136(b)(2) and 1910.261(i)(4).
(61) ANSI Z41-91, Personal Protection-Protective Footwear, IBR
approved for Sec. 1910.136(b)(1).
(62) ANSI Z48.1-54 Method for Marking Portable Compressed Gas
Containers to Identify the Material Contained, IBR approved for
Sec. Sec. 1910.103(b)(1)(i)(c); 1910.110(b)(5)(iii); and
1910.253(b)(1)(ii).
(63) ANSI Z48.1-54 (R 70) Method for Marking Portable Compressed Gas
Containers To Identify the Material Contained, IBR approved for
Sec. Sec. 1910.111(e)(1) and 1910.134(d)(4).
(64) ANSI Z49.1-67 Safety in Welding and Cutting, IBR approved for
Sec. 1910.252(c)(1)(iv) (A) and (B).
(65) ANSI Z53.1-67 Safety Color Code for Marking Physical Hazards
and the Identification of Certain Equipment, IBR approved for Sec. Sec.
1910.97(a)(3)(ii); 1910.145(d) (2), (4), and (6).
(66) ANSI Z54.1-63 Safety Standard for Non-Medical X-Ray and Sealed
Gamma Ray Sources, IBR approved for Sec. 1910.252(d) (1)(vii) and
(2)(ii).
(67) ANSI Z87.1-68 Practice of Occupational and Educational Eye and
Face Protection, IBR approved for Sec. Sec. 1910.133(b)(2);
1910.252(b)(2)(ii)(I); and 1910.261 (a)(3)(xxv), (d)(1)(ii), (f)(5),
(g)(10), (g)(15)(v), (g)(18)(ii), and (i)(4).
(68) ANSI Z87.1-89, Practice for Occupational and Educational Eye
and Face Protection, IBR approved for Sec. 1910.133(b)(1).
(69) ANSI Z88.2-69 Practices for Respiratory Protection, IBR
approved for Sec. Sec. 1910.94(c)(6)(iii)(a); 1910.134(c); and 1910.261
(a)(3)(xxvi), (b)(2), (f)(5), (g)(15)(v), (h)(2) (iii) and (iv), and
(i)(4).
(70) ANSI Z89.1-69 Safety Requirements for Industrial Head
Protection, IBR approved for Sec. Sec. 1910.135(b)(2); and 1910.261
(a)(3)(xxvii), (b)(2), (g)(15)(v), and (i)(4).
(71) ANSI Z89.1-86, Protective Headwear for Industrial Workers
Requirements, IBR approved for Sec. 1910.135(b)(1).
(72) ANSI Z89.2-71 Safety Requirements for Industrial Protective
Helmets for Electrical Workers, Class B, IBR approved for Sec.
1910.268(i)(1).
(f) The following material is available for purchase from the
American Petroleum Institute (API), 1220 L Street NW, Washington DC
20005:
(1) [Reserved]
(2) API 12B (May 1958) Specification for Bolted Production Tanks,
11th Ed., With Supplement No. 1, Mar. 1962, IBR approved for Sec.
1910.106(b)(1)(i)(a)(3).
(3) API 12D (Aug. 1957) Specification for Large Welded Production
Tanks, 7th Ed., IBR approved for Sec. 1910.106(b)(1)(i)(a)(3).
(4) API 12F (Mar. 1961) Specification for Small Welded Production
Tanks, 5th Ed., IBR approved for Sec. 1910.106(b)(1)(i)(a)(3).
(5) API 620, Fourth Ed. (1970) Including appendix R, Recommended
Rules for Design and Construction of Large Welded Low Pressure Storage
Tanks, IBR approved for Sec. Sec. 1910.103(c)(1)(i)(a);
1910.106(b)(1)(iv)(b)(1); and 1910.111(d)(1) (ii) and (iii).
(6) API 650 (1966) Welded Steel Tanks for Oil Storage, 3rd Ed., IBR
approved for Sec. 1910.106(b)(1)(iii)(a)(2).
(7) API 1104 (1968) Standard for Welding Pipelines and Related
Facilities, IBR approved for Sec. 1910.252(d)(1)(v).
(8) API 2000 (1968) Venting Atmospheric and Low Pressure Storage
Tanks, IBR approved for Sec. 1910.106(b)(2)(iv)(b)(1).
(9) API 2201 (1963) Welding or Hot Tapping on Equipment Containing
Flammables, IBR approved for Sec. 1910.252(d)(1)(vi).
(g) The following material is available for purchase from the
American Society of Mechanical Engineers (ASME), United Engineering
Center, 345 East 47th Street, New York, NY 10017:
[[Page 96]]
(1) ASME Boiler and Pressure Vessel Code, Sec. VIII, 1949, 1950,
1952, 1956, 1959, and 1962 Ed., IBR approved for Sec. Sec. 1910.110
(b)(10)(iii) (Table H-26), (d)(2) (Table H-31); (e)(3)(i) (Table H-32),
(h)(2) (Table H-34); and 1910.111(b)(2)(vi);
(2) ASME Code for Pressure Vessels, 1968 Ed., IBR approved for
Sec. Sec. 1910.106(i)(3)(i); 1910.110(g)(2)(iii)(b)(2); and
1910.217(b)(12);
(3) ASME Boiler and Pressure Vessel Code, Sec. VIII, 1968, IBR
approved for Sec. Sec. 1910.103; 1910.104(b)(4)(ii); 1910.106
(b)(1)(iv)(b)(2) and (i)(3)(ii); 1910.107; 1910.110(b)(11) (i)(b) and
(iii)(a)(1); 1910.111(b)(2) (i), (ii), and (iv); and 1910.169(a)(2) (i)
and (ii);
(4) ASME Boiler and Pressure Vessel Code, Sec. VIII, Paragraph UG-
84, 1968, IBR approved for Sec. 1910.104 (b)(4)(ii) and (b)(5)(iii);
(5) ASME Boiler and Pressure Vessel Code, Sec. VIII, Unfired
Pressure Vessels, Including Addenda (1969), IBR approved for Sec. Sec.
1910.261; 1910.262; 1910.263(i)(24)(ii);
(6) Code for Unfired Pressure Vessels for Petroleum Liquids and
Gases of the API and the ASME, 1951 Ed., IBR approved for Sec.
1910.110(b)(3)(iii); and
(7) ASME B56.6-1992 (with addenda), Safety Standard for Rough
Terrain Forklift Trucks, IBR approved for Sec. 1910.266(f)(4).
(h) The following material is available for purchase from the
American Society for Testing and Materials (ASTM), 1916 Race Street,
Philadelphia, PA 19103:
(1) ASTM A 47-68 Malleable Iron Castings, IBR approved for Sec.
1910.111(b)(7)(vi).
(2) ASTM A 53-69 Welded and Seamless Steel Pipe, IBR approved for
Sec. Sec. 1910.110(b)(8)(i) (a) and (b) and 1910.111(b)(7)(iv).
(3) ASTM A 126-66 Gray Iron Casting for Valves, Flanges and Pipe
Fitting, IBR approved for Sec. 1910.111(b)(7)(vi).
(4) ASTM A 391-65 (ANSI G61.1-1968) Alloy Steel Chain, IBR approved
for Sec. 1910.184(e)(4).
(5) ASTM A 395-68 Ductile Iron for Use at Elevated Temperatures, IBR
approved for Sec. 1910.111(b)(7)(vi).
(6) ASTM B 88-69 Seamless Copper Water Tube, IBR approved for Sec.
1910.110(b) (8)(i)(a) and (13)(ii)(b)(1).
(7) ASTM B 88-66A Seamless Copper Water Tube, IBR approved for Sec.
1910.252(d)(1)(i)(A)(2).
(8) ASTM B 117-64 Salt Spray (Fog) Test, IBR approved for Sec.
1910.268(g)(2)(i)(A).
(9) ASTM B 210-68 Aluminum-Alloy Drawn Seamless Tubes, IBR approved
for Sec. 1910.110(b)(8)(ii).
(10) ASTM B 241-69, IBR approved for Sec. 1910.110(b)(8)(i)
introductory text.
(11) ASTM D 5-65 Test for Penetration by Bituminous Materials, IBR
approved for Sec. 1910.106(a)(17).
(12) ASTM D 56-70 Test for Flash Point by Tag Closed Tester, IBR
approved for Sec. 1910.106(a)(14)(i).
(13) ASTM D 86-62 Test for Distillation of Petroleum Products, IBR
approved for Sec. Sec. 1910.106(a)(5) and 1910.119(b) ``Boiling
point.''
(14) ASTM D 88-56 Test for Saybolt Viscosity, IBR approved for Sec.
1910.106(a)(37).
(15) ASTM D 93-71 Test for Flash Point by Pensky Martens, IBR
approved for Sec. 1910.106(a)(14)(ii).
(16) ASTM D 323-68, IBR approved for Sec. 1910.106(a)(30)
(17) ASTM D 445-65 Test for Viscosity of Transparent and Opaque
Liquids, IBR approved for Sec. 1910.106(a)(37).
(18) ASTM D 1692-68 Test for Flammability of Plastic Sheeting and
Cellular Plastics, IBR approved for Sec. 1910.103(c)(1)(v)(d).
(19) ASTM D 2161-66 Conversion Tables For SUS, IBR approved for
Sec. 1910.106(a)(37).
(i) The following material is available for purchase from the
American Welding Society (AWS), 550 NW, LeJeune Road, P.O. Box 351040,
Miami FL 33135:
(1) AWS A3.0 (1969) Terms and Definitions, IBR approved for Sec.
1910.251(c).
(2) [Reserved]
(3) AWS B3.0-41 Standard Qualification Procedure, IBR approved for
Sec. 1910.67(c)(5)(i).
(4) AWS D1.0-1966 Code for Welding in Building Construction, IBR
approved for Sec. 1910.27(b)(6).
(5) AWS D2.0-69 Specifications for Welding Highway and Railway
Bridges, IBR approved for Sec. 1910.67(c)(5)(iv).
(6) AWS D8.4-61 Recommended Practices for Automotive Welding Design,
IBR approved for Sec. 1910.67(c)(5)(ii).
[[Page 97]]
(7) AWS D10.9-69 Standard Qualification of Welding Procedures and
Welders for Piping and Tubing, IBR approved for Sec.
1910.67(c)(5)(iii).
(j) The following material is available for purchase from the
Department of Commerce:
(1) Commercial Standard, CS 202-56 (1961) ``Industrial Lifts and
Hinged Loading Ramps,'' IBR approved for Sec. 1910.30(a)(3).
(2) Publication ``Model Performance Criteria for Structural Fire
Fighters' Helmets,'' IBR approved for Sec. 1910.156(e)(5)(i).
(k) The following material is available for purchase from the
Compressed Gas Association (CGA), 1235 Jefferson Davis Highway,
Arlington, VA 22202:
(1) CGA C-6 (1968) Standards for Visual Inspection of Compressed Gas
Cylinders, IBR approved for Sec. 1910.101(a).
(2) CGA C-8 (1962) Standard for Requalification of ICC-3HT
Cylinders, IBR approved for Sec. 1910.101(a).
(3) CGA G-1 (1966) Acetylene, IBR approved for Sec. 1910.102(a).
(4) CGA G-1.3 (1959) Acetylene Transmission for Chemical Synthesis,
IBR approved for Sec. 1910.102(b).
(5) CGA G-1.4 (1966) Standard for Acetylene Cylinder Charging
Plants, IBR approved for Sec. 1910.102(b).
(6) CGA G-7.1 (1966) Commodity Specification, IBR approved for Sec.
1910.134(d)(1).
(7) CGA G-8.1 (1964) Standard for the Installation of Nitrous Oxide
Systems at Consumer Sites, IBR approved for Sec. 1910.105.
(8) CGA P-1 (1965) Safe Handling of Compressed Gases, IBR approved
for Sec. 1910.101(b).
(9) CGA P-3 (1963) Specifications, Properties, and Recommendations
for Packaging, Transportation, Storage and Use of Ammonium Nitrate, IBR
approved for Sec. 1910.109(i)(1)(ii)(b).
(10) CGA S-1.1 (1963) and 1965 Addenda. Safety Release Device
Standards--Cylinders for Compressed Gases, IBR approved for Sec. Sec.
1910.101(c); 1910.103(c)(1)(iv)(a)(2).
(11) CGA S-1.2 (1963) Safety Release Device Standards, Cargo and
Portable Tanks for Compressed Gases, IBR approved for Sec. Sec.
1910.101(c); 1910.103(c)(1)(iv)(a)(2).
(12) CGA S-1.3 (1959) Safety Release Device Standards-Compressed Gas
Storage Containers, IBR approved for Sec. Sec.
1910.103(c)(1)(iv)(a)(2); 1910.104(b)(6)(iii); and
1910.111(d)(4)(ii)(b).
(13) CGA 1957 Standard Hose Connection Standard, IBR approved for
Sec. 1910.253(e) (4)(v) and (5)(iii).
(14) CGA and RMA (Rubber Manufacturer's Association) Specification
for Rubber Welding Hose (1958), IBR approved for Sec.
1910.253(e)(5)(i).
(15) CGA 1958 Regulator Connection Standard, IBR approved for Sec.
1910.253(e) (4)(iv) and (6).
(l) The following material is available for purchase from the Crane
Manufacturer's Association of America, Inc. (CMAA), 1 Thomas Circle NW,
Washington DC 20005:
(1) CMAA Specification 1B61, Specifications for Electric Overhead
Traveling Cranes, IBR approved for Sec. 1910.179(b)(6)(i).
(2) [Reserved]
(m) The following material is available for purchase from the
General Services Administration:
(1) GSA Pub. GG-B-0067b, Air Compressed for Breathing Purposes, or
Interim Federal Specifications, Apr. 1965, IBR approved for Sec.
1910.134(d)(4).
(2) [Reserved]
(n) The following material is available for purchase from the
Department of Health and Human Services:
(1) Publication No. 76-120 (1975), List of Personal Hearing
Protectors and Attenuation Data, IBR approved for Sec. 1910.95 App. B.
(2) [Reserved]
(o) The following material is available for purchase from the
Institute of Makers of Explosives (IME), 420 Lexington Avenue, New York,
NY 10017:
(1) IME Pamphlet No. 17, 1960, Safety in the Handling and Use of
Explosives, IBR approved for Sec. Sec. 1910.261 (a)(4)(iii) and
(c)(14)(ii).
(2) [Reserved]
(p) The following material is available for purchase from the
National Electrical Manufacturer's Association (NEMA):
(1) NEMA EW-1 (1962) Requirements for Electric Arc Welding
Apparatus, IBR approved for Sec. Sec. 1910.254(b)(1).
(2) [Reserved]
[[Page 98]]
(q) The following material is available for purchase from the
National Fire Protection Association (NFPA), 11 Tracy Drive, Avon, MA
02322:
(1) NFPA 30 (1969) Flammable and Combustible Liquids Code, IBR
approved for Sec. 1910.178(f)(1).
(2) NFPA 32-1970 Standard for Dry Cleaning Plants, IBR approved for
Sec. 1910.106(j)(6)(i).
(3) NFPA 33-1969 Standard for Spray Finishing Using Flammable and
Combustible Material, IBR approved for Sec. Sec. 1910.94(c) (1)(ii),
(2), (3) (i) and (iii), and (5).
(4) NFPA 34-1966 Standard for Dip Tanks Containing Flammable or
Combustible Liquids, IBR approved for Sec. 1910.124(b)(4)(iv).
(5) NFPA 34-1995 Standard for Dip Tanks Containing Flammable or
Combustible Liquids, IBR approved for Sec. 1910.124(b)(4)(ii).
(6) NFPA 35-1970 Standard for the Manufacture of Organic Coatings,
IBR approved for Sec. 1910.106(j)(6)(ii).
(7) NFPA 36-1967 Standard for Solvent Extraction Plants, IBR
approved for Sec. 1910.106(j)(6)(iii).
(8) NFPA 37-1970 Standard for the Installation and Use of Stationary
Combustion Engines and Gas Turbines, IBR approved for Sec. Sec.
1910.106(j)(6)(iv) and 1910.110 (b)(20)(iv)(c) and (e)(11).
(9) NFPA 51B-1962 Standard for Fire Protection in Use of Cutting and
Welding Processes, IBR approved for Sec. 1910.252(a)(1) introductory
text.
(10) NFPA 54-1969 Standard for the Installation of Gas Appliances
and Gas Piping, IBR approved for Sec. 1910.110(b)(20)(iv)(a).
(11) NFPA 54A-1969 Standard for the Installation of Gas Piping and
Gas Equipment on Industrial Premises and Certain Other Premises, IBR
approved for Sec. 1910.110(b)(20)(iv)(b).
(12) NFPA 58-1969 Standard for the Storage and Handling of Liquefied
Petroleum Gases (ANSI Z106.1-1970), IBR approved for Sec. Sec. 1910.110
(b)(3)(iv) and (i)(3) (i) and (ii); and 1910.178(f)(2).
(13) NFPA 59-1968 Standard for the Storage and Handling of Liquefied
Petroleum Gases at Utility Gas Plants, IBR approved for Sec. Sec.
1910.110 (b)(3)(iv) and (i)(2)(iv).
(14) NFPA 62-1967 Standard for the Prevention of Dust Explosions in
the Production, Packaging, and Handling of Pulverized Sugar and Cocoa,
IBR approved for Sec. 1910.263(k)(2)(i).
(15) NFPA 68-1954 Guide for Explosion Venting, IBR approved for
Sec. 1910.94(a)(2)(iii).
(16) NFPA 70-1971 National Electrical Code, IBR approved for Sec.
1910.66 App. D(c)(2).
(17) NFPA 78-1968 Lightning Protection Code, IBR approved for Sec.
1910.109(i)(6)(ii).
(18) NFPA 80-1968 Standard for Fire Doors and Windows, IBR approved
for Sec. 1910.106(d)(4)(i).
(19) NFPA 80-1970 Standard for the Installation of Fire Doors and
Windows, IBR approved for Sec. 1910.253(f)(6)(i)(I).
(20) NFPA 86A-1969 Standard for Oven and Furnaces Design, Location
and Equipment, IBR approved for Sec. Sec. 1910.107 (j)(1) and (l)(3)
and 1910.108 (b)(2) and (d)(2).
(21) NFPA 91-1961 Standard for the Installation of Blower and
Exhaust Systems for Dust, Stock, and Vapor Removal or Conveying (ANSI
Z33.1-61), IBR approved for Sec. 1910.107(d)(1).
(22) NFPA 91-1969 Standards for Blower and Exhaust Systems, IBR
approved for Sec. 1910.108(b)(1).
(23) NFPA 96-1970 Standard for the Installation of Equipment for the
Removal of Smoke and Grease Laden Vapors from Commercial Cooking
Equipment, IBR approved for Sec. 1910.110(b)(20)(iv)(d).
(24) NFPA 101-1970 Code for Life Safety From Fire in Buildings and
Structures, IBR approved for Sec. 1910.261(a)(4)(ii).
(25) NFPA 203M-1970 Manual on Roof Coverings, IBR approved for Sec.
1910.109(i)(1)(iii)(c).
(26) NFPA 251-1969 Standard Methods of Fire Tests of Building
Construction and Materials, IBR approved for Sec. Sec. 1910.106
(d)(3)(ii) introductory text and (d)(4)(i).
(27) NFPA 302-1968 Fire Protection Standard for Motor-Craft
(Pleasure and Commercial), IBR approved for Sec. 1910.265(d)(2)(iv)
introductory text.
(28) NFPA 385-1966 Recommended Regulatory Standard for Tank Vehicles
for Flammable and Combustible Liquids, IBR approved for Sec.
1910.106(g)(1)(i)(e)(1).
[[Page 99]]
(29) NFPA 496-1967 Standard for Purged Enclosures for Electrical
Equipment in Hazardous Locations, IBR approved for Sec.
1910.103(c)(1)(ix)(e)(1).
(30) NFPA 505-1969 Standard for Type Designations, Areas of Use,
Maintenence, and Operation of Powered Industrial Trucks, IBR approved
for Sec. 1910.110(e)(2)(iv).
(31) NFPA 566-1965 Standard for the Installation of Bulk Oxygen
Systems at Consumer Sites, IBR approved for Sec. Sec. 1910.253
(b)(4)(iv) and (c)(2)(v).
(32) NFPA 656-1959 Code for the Prevention of Dust Ignition in Spice
Grinding Plants, IBR approved for Sec. 1910.263(k)(2)(i).
(33) NFPA 1971-1975 Protective Clothing for Structural Fire
Fighting, IBR approved for Sec. 1910.156(e)(3)(ii) introductory text.
(r) The following material is available for purchase from the
National Food Plant Institute, 1700 K St. NW., Washington, DC 20006:
(1) Definition and Test Procedures for Ammonium Nitrate Fertilizer
(Nov. 1964), IBR approved for Sec. 1910.109 Table H-22, ftn. 3.
(2) [Reserved]
(s) The following material is available for purchase from the
National Institute for Occupational Safety and Health (NIOSH):
(1) Registry of Toxic Effects of Chemical Substances, 1978, IBR
approved for Sec. 1910.20(c)(13)(i) and appendix B.
(2) Development of Criteria for Fire Fighters Gloves; Vol. II, Part
II; Test Methods, 1976, IBR approved for Sec. 1910.156(e)(4)(i)
introductory text.
(3) NIOSH Recommendations for Occupational Safety and Health
Standards (Sept. 1987), IBR approved for Sec. 1910.120 PEL definition.
(t) The following material is available for purchase from the Public
Health Service:
(1) U.S. Pharmacopeia, IBR approved for Sec. 1910.134(d)(1).
(2) Publication No. 934 (1962), Food Service Sanitation Ordinance
and Code, Part V of the Food Service Sanitation Manual, IBR approved for
Sec. 1910.142(i)(1).
(u) The following material is available for purchase from the
Society of Automotive Engineers (SAE), 485 Lexington Avenue, New York,
NY 10017:
(1) SAE J185, June 1988, Recommended Practice for Access Systems for
Off-Road Machines, IBR approved for Sec. 1910.266(f)(5)(i).
(2) SAE J231, January 1981, Minimum Performance Criteria for Falling
Object Protective Structure (FOPS), IBR approved for Sec.
1910.266(f)(3)(ii).
(3) SAE J386, June 1985, Operator Restraint Systems for Off-Road
Work Machines, IBR approved for Sec. 1910.266(d)(3)(iv).
(4) SAE J397, April 1988, Deflection Limiting Volume-ROPS/FOPS
Laboratory Evaluation, IBR approved for Sec. 1910.266(f)(3)(iv).
(5) SAE 765 (1961) SAE Recommended Practice: Crane Loading Stability
Test Code, IBR approved for Sec. 1910.180 (c)(1)(iii) and
(e)(2)(iii)(a).
(6) SAE J1040, April 1988, Performance Criteria for Rollover
Protective Structures (ROPS) for Construction, Earthmoving, Forestry and
Mining Machines, IBR approved for Sec. 1910.266(f)(3)(ii).
(v) The following material is available for purchase from the
Fertilizer Institute, 1015 18th Street NW, Washington, DC 20036:
(1) Standard M-1 (1953, 1955, 1957, 1960, 1961, 1963, 1965, 1966,
1967, 1968), Superseded by ANSI K61.1-1972, IBR approved for Sec.
1910.111(b)(1) (i) and (iii).
(2) [Reserved]
(w) The following material is available for purchase from
Underwriters Laboratories (UL), 207 East Ohio Street, Chicago, IL 60611:
(1) UL 58-61 Steel Underground Tanks for Flammable and Combustible
Liquids, 5th Ed., IBR approved for Sec. 1910.106(b)(1)(iii)(a)(1).
(2) UL 80-63 Steel Inside Tanks for Oil-Burner Fuel, IBR approved
for Sec. 1910.106(b)(1)(iii)(a)(1).
(3) UL 142-68 Steel Above Ground Tanks for Flammable and Combustible
Liquids, IBR approved for Sec. 1910.106(b)(1)(iii)(a)(1).
[39 FR 23502, June 27, 1974, as amended at 49 FR 5321, Feb. 10, 1984; 61
FR 9231, Mar. 7, 1996; 64 FR 13908, Mar. 23, 1999; 69 FR 18803, Apr. 9,
2004; 70 FR 53929, Sept. 13, 2005]
Effective Date Note: At 72 FR 7190, Feb. 14, 2007, Sec. 1910.6 was
amended by revising the introductory text to paragraph (e), removing
[[Page 100]]
and reserving paragraph (e)(33), revising the introductory text to
paragraph (q), and removing and reserving paragraph (q)(16), effective
Aug. 13, 2007. For the convenience of the user, the revised text is set
forth as follows:
Sec. 1910.6 Incorporation by reference.
* * * * *
(e) The following material is available for purchase from the
American National Standards Institute (ANSI), 25 West 43rd Street,
Fourth Floor, New York, NY 10036:
* * * * *
(q) The following material is available for purchase from the
National Fire Protection Association (NFPA), 1 Batterymarch Park,
Quincy, MA 02269:
* * * * *
